For about two years now I've had an issue with my motor when I go from high speeds to back down to low speeds like when I go into a slow no wake area. The motor would either die or I needed to pump the bulb to give it more fuel. I eliminated the possibility of it being the fuel pump because people I talked to, including a mechanic and Googling it said if it was a fuel pump issue I'd run out of fuel at high speeds as well. Anyone else have an issue like this?
Motor Being Starved Of Fuel At Low Speeds
I was aware of the primer bulb only being used for when the motor is not running. But I was told by many that the motor would die at WOT if the fuel pump was bad. I replaced the bulb in the past and the fuel line and I struggled to get the bulb hard. By process of elimination next thing to try was the tank. It always seemed like I had a hard time getting the bulb hard, so I think the connection into the tank didn't fully "click" and was loose.
So far everything seems to be working correctly since I replaced the fuel tank. I ran my motor a lot this past week and a fair amount at slow speeds and it did not die on me one time! I know it might take even more to confirm that the issue is fixed, but so far so good.
Brent Hess.....that might be the most well explained reasoning I have read. Well put.
I had the same problem with a mercury motor.It was the bulb, I bought a mercury replace ment, same thing. Went to fleet farm and bought a Atwood brand, a whole new gas line. Problem solved. Been about 15 yrs now.Hope thus helps.
The primer bulb’s only purpose is to get gas into the carburetor when the motor is not running.
After the motor is running, the fuel pump takes over.
Also, the primer bulb has a check valve in it, and if it is beginning to fail, there is nothing to stop the fuel (via gravity) from going back into the tank.
At WOT, you don’t really notice it, as the fuel pump has taken over, however, at idle speeds, a bad check valve, or air leak in the fuel line can give you continual grief.
If you have to continually pump the bulb to keep your motor running, you have one of three issues 1) Bad check valve in the bulb 2) Air leak in your fuel line 3) Bad or failing diaphragm in your fuel pump
Yes, my new tank has that new pressure valve on it. Finally the bulb has been staying hard. I've run it for as much as 10 minutes at a time at slow no wake speeds and motor is running great. Before with the original tank I didn't lake 2 minutes at slow speeds and the bulb was soft and motor would die. It was a pain in the ass continuing to pump the bulb while moving. My problem has been I'm too cheap to take it in to have a mechanic look at it, but I think I fixed it with getting the new fuel tank, so if this permanently works then I saved myself a few hundred dollars for not having to have a mechanic look at it!
BTW, I did open the motor cover and pumped gas thru the line to check for any leaks at all before I bought the tank and I couldn't find any what so ever.
My new Suzuki does it at wot but only on occasion, boat comes to a stop and pump the ball and it fires riteback up what the hell would cause that? Thinking the water seperator filter..
Fishloveme, I repowered my Jon boat with a 2020 25 hp Mercury 4 stroke. It came with a fuel tank equipped with a pressure sensitive valve that will only allow 5 psi of fuel pressure to the motor. New EPA regulations require that the fuel tank can’t vent like the normal ones did. The fill cap still has a vent that you can open and it will release the pressure if it gets too great to prevent tank rupture. The tank also came with the grey gas line that is stiff as a broomstick, that gas line is considered non permeable, that is it doesn’t allow gas vapor to be emitted through the line itself. I asked about using my old, 1999 fuel tank. Dealer mechanic who walked me through the motor operation said the new motors would run poorly if at all on the older style tanks that didn’t build pressure. With your motor being a 2000 it must be a carbureted 2 stroke. I wonder how that will react with a pressurized fuel supply.
My motor is a 2000 Mercury 50 HP tiller.
So far so good after I replaced the fuel tank. I've been running the motor at slow speeds all week while fishing on my vacation. It seemed to me that the problem had gotten worse recently, to the point where I had issues even getting the bulb hard. Twice I replaced the fuel line and bulb and it seemed to help a little for a while, but this last time it didn't help at all. But replacing the gas tank has done the trick so far.
Now, question for everyone. I spent the extra money and bought a Mercury brand fuel tank. It has a special stop valve on it so that fuel won't back into the motor (or so they claim). At the dealership they claimed the ones you can get at Walmart or Fleet Farm are useless because they blow up like a balloon (I've seen this with a tank I had for my 10 horse Evinrude). Do you think there's any truth to this about those cheap tanks not working well with these motors, or could I have probably been fine with it?
Check the fuel line they get hard around the hose barbs and suck air
Need more info,like year/make.Could be also those crappy fuel lines that EPA mandated.