MENU
Lake-Link Home
LOGIN
Lake-Link
LOG IN

1981 50 horse evinrude had all water in lower unit?

8/21/19 @ 9:37 PM
ORIGNAL POST
walleyejak3
walleyejak3
User since 12/3/18

All water and a touch of creamy oil. Came back off Bago  The engine suddenly bogs down and starts making a terrible sound. Like something grinding… metal on metal?? Then I put my Minn kota down to bring me in and it would keep pulsating every 3 seconds?? Ideas please I just bought this boat. UURRRGGGG. Stay on top! Wj

DISPLAYING 1 TO 9 OF 9 POSTS
FILTER OPTIONS
9/3/19 @ 6:34 PM
chaw
User since 9/11/02

WJ- Sounds like you have her going in the right direction. Hope she runs smooth for you.

9/2/19 @ 2:36 PM
walleyejak3
walleyejak3
User since 12/3/18

Update... The bottom lower unit screw had no washer on it. I put new oil in and just got off the water . Went in reverse no noise went out into lake fast no noise! Took prop off trolling motor and stripped a bunch of line off. The trolling motor works now! Im going to change oil again and put in a magnetic screw.



8/24/19 @ 9:00 PM
Plmlk
Brent Hess
MEMBER since 12/18/07

Drain the lower unit and put the oil through a coffee filter or even a paper towel.  If you see metal shavings it’s all bad...

You mentioned hearing a metal on metal grinding noise, I’m guessing your lower unit is toast. 

The cheapest route is to find a motor with a blown power head, and change out the lower unit.

Or you could buy a new lower unit for around 1,700...

 

The Woodlands Resort
(262) 661-3968
8/24/19 @ 8:08 PM
walleyejak3
walleyejak3
User since 12/3/18

Thanks guys! Where should I start? I'm going to fix it myself. Do I put oil in and try it out or start by taking it apart?

8/23/19 @ 10:50 AM
KevinS
MEMBER since 9/24/08

Not uncommon for older motor to have a little water mixed in, when does, time to change the prop seal, fairly easy to do, and may have to make your own tool threads to put bearing housing back in.  I did that to my 60 couple of years ago.  You may want to check the shift linkage height, just pull lower unit, ensure in neutral, look up in manual says what measurement is.  Use a yard stick, tape a drill bit on it, works for measuring.  If off, will get some grinding.   Just purchased larger boat, so, have mine on market, and I have extra lower unit with it just in case, someone tossed a 70, so, took some parts off of it to convert to non VRO, and kept it.   This new Yamaha, doubt if I can do much work on it except for changing impeller,  etc on it.  All electronic stuff.  

8/22/19 @ 7:33 PM
Plmlk
Brent Hess
MEMBER since 12/18/07

If you heard metal grinding, your lower unit is shot...

You likely have a bad seal which allowed water into your lower unit.  

Your best bet is to buy a new / refurbished lower unit.  

A second option would be to find a blown motor, you can get them for pretty much nothing, and just swap out the lower unit.  

When you are looking at purchasing a new / used motor, always remove the lower unit plug to see what comes out.  Some folks will sell you their problems without regret.

Also, a lake test is an absolute must.  A motor with lower unit issues will run just fine on the muffs, but can't handle the torque required to get the boat on plane. 


The Woodlands Resort
(262) 661-3968
8/22/19 @ 8:25 AM
chaw
User since 9/11/02

You probably blew a seal on the lower unit which allowed oil to drain out and water to get in and created the sludge you see. Hopefully you shut the motor down before it got too bad.

I had the same issue a couple weeks ago and luckily noticed an oil slick in the water before I started the motor. I put it back on the trailer to discover the gray sludge. 

8/22/19 @ 6:19 AM
Fishlovme
Fishlovme
MEMBER since 6/22/01

I made the mistake of not checking the lower unit of a motor I bought one time. Never again! I was on the lake when the shaft completely snapped in half - there wasn't a single drop of oil left! Always check the motor over throroghly, it's one of the most expensive parts of the investment! And of there's a trolling motor check thru that too! Looks like you'll have repairs to do. Mine was a 25 hp and instead of spending 400 bucks to fix the motor i sold it for parts instead and eventually I sold the boat as well!

DISPLAYING 1 TO 9 OF 9 POSTS
Advertise here
Advertise here
Please take a moment to visit our sponsors. Without them we would not be here.